cgutils, and define them so they are no larger than what is required by
the current target platform
* added cgutils to the uses clause of several units that use the
tcpuregisterset type
git-svn-id: trunk@21624 -
always points to the previous r7 on the stack (with the saved return
address coming right after it) so that the debugger and crashreporter
can use it for backtraces as specified in the ABI
o changed NR_FRAME_POINTER_REG and RS_FRAME_POINTER_REG from a symbolic
into a typed constant, and added a new method to tprocinfo that can
be used to initialze it (so it can be inited to r7/r11 depending on
the target platform)
* allow using r9 on Darwin, it was only used by the system on iOS up to
2.x, which we no longer support
* prefer using r9 and r12 before r4..r11 on Darwin, because they are
volatile and hence do not have to be saved
git-svn-id: trunk@20661 -
o new eabihf (hard float) abi
o vfpv3_d16 variant of VFP (default variant used by EABI assemblers: VFPv3
with only 16 double registers instead of 32) and pass it to GNU as
o make the odd numbered single precision floating point VFP registers
available for explicit allocation for use by the calling convention
* fixed copy/paste error in stdname of S30 register
-> use -dFPC_ARMHF to create an ARM eabi hard float compiler
(mantis #21554)
git-svn-id: trunk@20660 -
+ RTL support:
o VFP exceptions are disabled by default on Darwin,
because they cause kernel panics on iPhoneOS 2.2.1 at least
o all denormals are truncated to 0 on Darwin, because disabling
that also causes kernel panics on iPhoneOS 2.2.1 (probably
because otherwise denormals can also cause exceptions)
* set softfloat rounding mode correctly for non-wince/darwin/vfp
targets
+ compiler support: only half the number of single precision
registers is available due to limitations of the register
allocator
+ added a number of comments about why the stackframe on ARM is
set up the way it is by the compiler
+ added regtype and subregtype info to regsets, because they're
also used for VFP registers (+ support in assembler reader)
+ various generic support routines for dealing with floating point
values located in integer registers that have to be transferred to
mm registers (needed for VFP)
* renamed use_sse() to use_vectorfpu() and also use it for
ARM/vfp support
o only superficially tested for Linux (compiler compiled with -Cpvfpv6
-Cfvfpv2 works on a Cortex-A8, no testsuite run performed -- at least
the fpu exception handler still needs to be implemented), Darwin has
been tested more thoroughly
+ added ARMv6 cpu type and made it default for Darwin/ARM
+ ARMv6+ implementations of atomic operations using ldrex/strex
* don't use r9 on Darwin/ARM, as it's reserved under certain
circumstances (don't know yet which ones)
* changed C-test object files for ARM/Darwin to ARMv6 versions
* check in assembler reader that regsets are not empty, because
instructions with a regset operand have undefined behaviour in that
case
* fixed resultdef of tarmtypeconvnode.first_int_to_real in case of
int64->single type conversion
* fixed constant pool locations in case 64 bit constants are generated,
and/or when vfp instructions with limited reach are present
WARNING: when using VFP on an ARMv6 or later cpu, you *must* compile all
code with -Cparmv6 (or higher), or you will get crashes. The reason is
that storing/restoring multiple VFP registers must happen using
different instructions on pre/post-ARMv6.
git-svn-id: trunk@14317 -
(override/adjust cgutils.use_fixed_stack to change conditions where
this is done, currently only activated for darwin-i386)
* make sure the stack is always aligned to 16 bytes on darwin-i386
git-svn-id: trunk@2840 -
