Precisize rules for selection of thumb instructions.
Add short-cut notation support for most simple Thumb2 instructions ( add r1,#4 instead of add r1,r1,#4 ).
git-svn-id: branches/laksen/armiw@29343 -
Move ThumbFunc flag from section to symbol.
Make .w forms optional the other way around. If .w is explicitly put on an instruction the assembler should always chose a wide form.
git-svn-id: branches/laksen/armiw@29341 -
Fixed bug in Mov instruction.
Added initial scanning of IT/LastInIT detection for proper instruction selection.
Disabled "wide" format flag detection again for now.
git-svn-id: branches/laksen/armiw@29338 -
Fixed a bunch of instruction encodings by comparing bulks of handwritten tests to binutils assembled versions.
Fixed emission of regsets of S and D registers above 15.
Fixed assembler reader for RRX shiftmode.
There can be a size postfix after a condition code in UAL assembler syntax. This has been added to the assembler reader.
git-svn-id: branches/laksen/armiw@29277 -
Add some VFP registers.
Rebuilt tables.
Added a lot of VFPv3 and Advanced SIMD(not supported yet) oppostfixes.
Implemented code in aasmcpu to generate binary code from the instructions. Only ARM32 supported so far.
git-svn-id: branches/laksen/armiw@29246 -
Add simple Mul+Sub/Mul+Add into MLS/MLA optimizations
Fix some other small issues in the optimizer
Implement Interlocked* functions with proper use of LDREX/STREX
git-svn-id: branches/laksen/arm-embedded@22801 -
Create preliminary Thumb-2 PeepHoleOptPass2 code, hacked together from the ARM mode code
Added a number of simple size optimizations for common Thumb-2 instructions
git-svn-id: branches/laksen/arm-embedded@22590 -
Fix problem with loading of condition operand for IT instructions
Properly split IT blocks when register allocator tries to spill inside a block.
git-svn-id: branches/laksen/arm-embedded@22582 -
and add usermode parsing of LDM/STM ops
This patch basically extends the ARM assembly reader a bit to properly parse CPSR and
SPSR flags for the MSR opcode, and allows the reader to understand
the ^ modifer for register lists for STMxx and LDMxx.
Previously the following combinations weren't possible in straight assembler:
MRS R0, CPSR
MRS R0, SPSR
MSR CPSR_CX, R0
LDMIA SP, {R0-R15}^
etc..
git-svn-id: trunk@22502 -
The old version did not check the S-Postfix for MOV, which results in
removing instructions like:
movs r0, r0
which breaks later flag usage.
git-svn-id: trunk@21676 -
* generate add.w instead of add for thumb-2 in case one of the registers
is > r8
* add register interferences for the "add" instruction so the register
allocator can detect invalid instruction forms (even for assembler code)
* fixed error in thumb2.inc detected by the previous change
git-svn-id: trunk@16633 -
solves the problem whereby an empty list could sometimes be inserted
after a jump table load (in case the jump table was larger than the
maximally allowed offset, and if there was a skipinstr between the
previous instruction and the jump table load) (mantis #17164)
git-svn-id: trunk@15831 -
+ RTL support:
o VFP exceptions are disabled by default on Darwin,
because they cause kernel panics on iPhoneOS 2.2.1 at least
o all denormals are truncated to 0 on Darwin, because disabling
that also causes kernel panics on iPhoneOS 2.2.1 (probably
because otherwise denormals can also cause exceptions)
* set softfloat rounding mode correctly for non-wince/darwin/vfp
targets
+ compiler support: only half the number of single precision
registers is available due to limitations of the register
allocator
+ added a number of comments about why the stackframe on ARM is
set up the way it is by the compiler
+ added regtype and subregtype info to regsets, because they're
also used for VFP registers (+ support in assembler reader)
+ various generic support routines for dealing with floating point
values located in integer registers that have to be transferred to
mm registers (needed for VFP)
* renamed use_sse() to use_vectorfpu() and also use it for
ARM/vfp support
o only superficially tested for Linux (compiler compiled with -Cpvfpv6
-Cfvfpv2 works on a Cortex-A8, no testsuite run performed -- at least
the fpu exception handler still needs to be implemented), Darwin has
been tested more thoroughly
+ added ARMv6 cpu type and made it default for Darwin/ARM
+ ARMv6+ implementations of atomic operations using ldrex/strex
* don't use r9 on Darwin/ARM, as it's reserved under certain
circumstances (don't know yet which ones)
* changed C-test object files for ARM/Darwin to ARMv6 versions
* check in assembler reader that regsets are not empty, because
instructions with a regset operand have undefined behaviour in that
case
* fixed resultdef of tarmtypeconvnode.first_int_to_real in case of
int64->single type conversion
* fixed constant pool locations in case 64 bit constants are generated,
and/or when vfp instructions with limited reach are present
WARNING: when using VFP on an ARMv6 or later cpu, you *must* compile all
code with -Cparmv6 (or higher), or you will get crashes. The reason is
that storing/restoring multiple VFP registers must happen using
different instructions on pre/post-ARMv6.
git-svn-id: trunk@14317 -
